|
|
Cruiser
Posts: 127
OHIO | Anybody know what size allen wrench the front axle is? I used the backside of a 3/4 inch punch to get mine out to change the front tire. I want to get the right size hex socket. I'm guessing it is 16 or 17mm. Thanks, |
|
| |
|
Visionary
Posts: 3773
Pittsburgh, PA | 16 |
|
| |
|
Visionary
Posts: 1359
New Bohemia, Va | good luck trying to find that. go to Sears and get a 5/8 allen 1/2 drive. |
|
| |
|
Iron Butt
Posts: 721
| +1 on what Allen said except I got mine at Auto Zone. |
|
| |
|
Visionary
Posts: 3773
Pittsburgh, PA | Harbor freight is where I got a entire kit of Allen's including the 16mm for $9.95 |
|
| |
|
Visionary
Posts: 3006
San Antonio, TX | Arkainzeye - 2011-06-28 5:34 AM
Harbor freight is where I got a entire kit of Allen's including the 16mm for $9.95
Do you have their part number? |
|
| |
|
Cruiser
Posts: 130
Houston, Tx | That is one size that is hard to locate as part of a set as most go from 14mm to 17mm for some unknown reason. I was able to find many locations to purchase as a single piece, here's one example from Amazon
I'm sure there are others, may even be able to locate within local Ace / Lowe's / ect ...
Edited by BlueByu 2011-06-28 3:05 PM
|
|
| |
|
Visionary
Posts: 1359
New Bohemia, Va | Make it easy on yourself and, go to sears and get the 5/8, 1/2 drive allen, normally readily available, or can be ordered and shipped quickly, too easy. |
|
| |
|
Cruiser
Posts: 127
OHIO | Looking through Harbor Freight sale catalog ending 7/31, I see 9 piece 3/8" and 1/2" drive hex bit socket sets. Metric Lot No. 67880/98229 3/8" drive: 4mm to 10mm 1/2" drive 12mm to 17mm On sale for $9.99 Doesn't say anything about if 16mm is in it. I will be checking it out. Thanks for the replies. |
|
| |
|
Cruiser
Posts: 127
OHIO | I visited Harbor Freight yesterday and they do not have 16mm hex bit socket. There sets go from 14mm to 17mm. I ordered a 16mm from Amazon. |
|
| |
|
Visionary
Posts: 3006
San Antonio, TX | I do have the 5/8" hex. In fact I have two. I know it is only 4 thousands smaller. Even so I know that someday I will buy a 16mm.
Ride Safe
Edited by radioteacher 2011-07-02 10:54 AM
|
|
| |
|
Visionary
Posts: 1359
New Bohemia, Va | radioteacher - 2011-07-02 10:54 AM
I do have the 5/8" hex. In fact I have two. I know it is only 4 thousands smaller. Even so I know that someday I will buy a 16mm.
Ride Safe
if you soak in water for about 3 hours it will swell up to 16mm.  |
|
| |
|
Visionary
Posts: 3773
Pittsburgh, PA | It's not the size of the Allen, its how you use it! |
|
| |
|
Visionary
Posts: 1359
New Bohemia, Va |  |
|
| |
|
Visionary
Posts: 3006
San Antonio, TX | After reading what I wrote....that I know is true....I am smiling too. |
|
| |
Front axle size?
