|
|
Tourer
Posts: 482
Beer Collins, Colorado (there is no fort) | My PIAA NightTech bulbs are doing great but I've been checking around for the next time I have to do a bulb change and came across a set up to change both bulbs to HID for $70-What do you think?
http://www.ddmtuning.com/Products/DDM-35W-55W-Dual-Motorcycle-HID-K... |
|
| |
|
Visionary
Posts: 4278
| you want to look close I think there car one pretty cheap from what I see
here are some higher price but I trust thih guy he is one of us
http://www.victoryhid.com/index.php |
|
| |
|
Tourer
Posts: 482
Beer Collins, Colorado (there is no fort) | specs look to be the same at 1/2 the price |
|
| |
|
Tourer
Posts: 466
Grand Cane, LA | ByteN2it, that is the same kit I have on my bike. I have the 55 watt kit with the 6000k color bulbs. The color is slightly bluish. If you're trying to match the center factory HID get the 4300k color. I've had my kit for about a year now without a single problem.
(5111.jpg)
Attachments
----------------
 5111.jpg (98KB - 4 downloads)
|
|
| |
|
Tourer
Posts: 466
Grand Cane, LA | Also, my kit doesn't "take a minute" to brighten up. It's an instant change from low to high beam. |
|
| |
|
Tourer
Posts: 482
Beer Collins, Colorado (there is no fort) | Not trying to match my HID center driving light.
I'm looking to convert the two H4 halogens to 5000K hi/low HID.
Johnnyvision-Tell me these aren't the same kits-one is just marked up 110%-which one would you buy?
Edited by ByteN2it 2012-09-02 10:46 PM
(hidbikesingle.jpg)
(hidkit.jpg)
Attachments
----------------
hidbikesingle.jpg (51KB - 0 downloads)
hidkit.jpg (21KB - 0 downloads)
|
|
| |
|
Puddle Jumper
Posts: 48
Cornwall England | That's an excellent price and a excellent find.
Do I take it that this will simply be a swap out for the regular H4 lights with the ballast boxs being stowed somewhere secure?
Steve |
|
| |
|
Visionary
Posts: 4278
| OK OK you got me.
Would like to see your right up on your install. Will spend my money there |
|
| |
|
Tourer
Posts: 466
Grand Cane, LA | The 5000k will be real close to the same color as the HID factory light. 4300k is about the same as the halogen bulb color. The higher you go in color temperature the more blue the light gets. |
|
| |
|
Tourer
Posts: 466
Grand Cane, LA | On a side note, when you install the bulbs make sure that when they pull in that the bulb pulls back in and up. When I first tried mine the bulbs pulled in and down and the high beam was all screwed up. The bulbs come with a special reflector on them for our bikes, but the bulb can be put into the reflector wrong from the factory. Just hook up some power to the 2 little wires (red and black) and cycle it to see which way it ends up in the reflector. Will save you a whole lot of headache before getting all back assembled. Believe me, I found out the hard way.
Big Steve: It is a somewhat simple swap out with a little wiring to do. You have to provide a power source for the hi/lo function to work. The bulbs pull back for the high beam.
Edited by atvtinker 2012-09-03 10:00 PM
|
|
| |
|
Puddle Jumper
Posts: 48
Cornwall England | atvtinker - 2012-09-03 3:56 AM It is a somewhat simple swap out with a little wiring to do. You have to provide a power source for the hi/lo function to work. The bulbs pull back for the high beam. Would that be a separate power source in addition to the one supplied by the original hi/lo wiring?
|
|
| |
|
Tourer
Posts: 466
Grand Cane, LA | Yes. The hi/lo function is determined by the pull back action of the bulb. The original hi/lo function is powering two different elements in the bulb. All you have to do is find a power source. I ran my power directly to the battery. This way when I have my lights on and not running I can still swap to high beams. It comes with a fused lead and everything still has to go through the relay set-up provided. There are a couple of places up front you could tie into, I just never took the time to search them out. |
|
| |
|
Puddle Jumper
Posts: 48
Cornwall England | Many thanks atvtinker for the info. I have an order in but they have problems sending it to the UK so I have a query opened with them. - Steve |
|
| |
|
Tourer
Posts: 466
Grand Cane, LA | I hope they can get them to you. They usually have some in stock in CA so maybe they can ship them to you from there rather than from their warehouse. I know the second set I ordered for my friend came from their warehouse and it took twice as long to get them. Good luck. |
|
| |
|
Tourer
Posts: 482
Beer Collins, Colorado (there is no fort) | Update-high beam went out on my right side PIAA NightTech bulb the other day, lasted just over a year & 12,000 miles. I just ordered a HID kit that will make for a nice little winter project (just had our first taste of snow today) got the 55W 5000K H4 Dual Hi/low kit for $65 + shipping
http://www.ddmtuning.com/Products/DDM-35W-55W-Dual-Motorcycle-HID-K...
I'll plan on taking a few pics of the procedure when I get to it-Brian |
|
| |
|
Iron Butt
Posts: 1066
Peru, IN | I just want a detailed write up (with pics) on the process used to install them. From what I'm reading, you have to disassemble the front half of the fairing. Not really sure I'm into that with my "skillz". |
|
| |
|
Tourer
Posts: 482
Beer Collins, Colorado (there is no fort) | For me it's easiest so simply remove the tuppeware and pull the headlight module out (I wear a size 15 ring & 4XL gloves)-took me about an hour each way last time I did a bulb change-MM,I haven't messed with my stock HID driving light but I'm pretty sure once the module is accessable it would be a simple bulb change and mounting of the ballast. I had my original HID replaced when I noticed a piece rolling around inside the module-they replaced the whole module with a new one that I see now has a screw holding the shroud at the HID bulb. I'm going to all three headlights being HID and see how it looks. Removing the pieces to get at the headlight requires more patience than skill-get your service manual out or get you wallet out, your choice. |
|
| |
|
Iron Butt
Posts: 1066
Peru, IN | Service manual should be here tomorrow (Friday). I'll have to look at the pics and see if I'm up for it. If not, I'll need to find a decent shop who can do it. |
|
| |
|
Cruiser
Posts: 207
| I changed the center bulb to HID a couple of weekends ago. Took me about four hours total. Did a search on this forum for threads with instructions and just followed along. |
|
| |
|
Iron Butt
Posts: 1066
Peru, IN | Direct me to those threads, please. I can't find anything although I may be been using the wrong search terms. |
|
| |
|
Tourer
Posts: 482
Beer Collins, Colorado (there is no fort) | Started the HID upgrade this afternoon and it's going well-I got the ddm H4 hi/low dual 55w kit in 5000K ($80 with shipping) Got the module pulled quite easy this time now that I know what I'm doing(20min/1beer) the bulbs just simply swap and plug everything together. Lit right up when I started the bike and the hi/low switch mechanically tilts the bulb so the light is constantly on just refocused. It's damn bright, I can still see them when I close my eyes. Just have to sort the wiring and get the mini ballasts mounted up inside the faring-it's going to be a cold weekend so I'll take my time and post some pics along the way. Brian
(phppsfnG5PM.jpg)
(phpM3j3bvPM.jpg)
(php3fM9BjPM.jpg)
(phpdHPCmYPM.jpg)
Attachments
----------------
phppsfnG5PM.jpg (59KB - 0 downloads)
phpM3j3bvPM.jpg (58KB - 0 downloads)
php3fM9BjPM.jpg (61KB - 0 downloads)
phpdHPCmYPM.jpg (29KB - 0 downloads)
|
|
| |
|
Tourer
Posts: 482
Beer Collins, Colorado (there is no fort) | Got a little further sorting out the wiring-got the ballasts & hi/low relays mounted - a few more flips of the wrist & I'll be ready for a test run and aim adjustment.
(php4v4OngAM.jpg)
(phpH5rOvOAM.jpg)
(php6t98HyAM.jpg)
Attachments
----------------
php4v4OngAM.jpg (62KB - 2 downloads)
phpH5rOvOAM.jpg (44KB - 2 downloads)
php6t98HyAM.jpg (84KB - 2 downloads)
|
|
| |
|
Tourer
Posts: 482
Beer Collins, Colorado (there is no fort) | Watched the Bronco game then out to the shop and finished the HID upgrade. The stock HID cyclops driving light now looks like a soft white 60w incandescent bulb compared to the new headlights. Hopefully I wont have to mess with the headlight for a good long while.
(phpjmDDB7PM.jpg)
Attachments
----------------
phpjmDDB7PM.jpg (67KB - 0 downloads)
|
|
| |
|
Tourer
Posts: 457
Green Bay, WI United States | I am not sure about this replacement of stock vs HID bulbs but I currently get flashed to get off the brights with the stock bulbs on low and the center HID on. I like the idea of seeing and being seen but as my buddy said, "Meeting your Bike on the road is obnoxiousness". Looking for feedback, and as I have always said being seen on a bike is priceless.......
|
|
| |
|
Tourer
Posts: 482
Beer Collins, Colorado (there is no fort) | If your getting flashed on low beam I would check the aim on your headlight. Night riding makes up a very small percentage of my riding but when I do I want the absolute best I can get and this is by far the best bang for the buck that I've found. I've heard the "it's illegal" arguments but technically so are my pipes so WTF- at least the deer will hear me coming I'll see them- & we'll all make it home safe. Brian |
|
| |
HID Headlights
