You are currently not logged in.  Logon or register to access more features. Vision-Riders.com is a FREE service provided by Victory Riders Network.

Search:




Anybody install their own Power Commander V?
Jump to page : 1
Now viewing page 1 [25 messages per page]		View previous thread :: View next thread
   Discussion -> Vision Tech Q&AMessage format
 
nailer
Posted 2016-08-06 4:30 PM (#188023)
Subject: Anybody install their own Power Commander V?


Tourer

Posts: 366
Albuquerque, NM		Any problems on initial start? Mine won't idle and getting an check engine light. Double checked all connections. Downloaded a map very close to my setup.
Top of the page Bottom of the page
johnnyvision
Posted 2016-08-06 5:33 PM (#188024 - in reply to #188023)
Subject: Re: Anybody install their own Power Commander V?


Visionary

Posts: 4278
what did you ground it to. Go straight to frame.

do you have all wires pressed in tight
Top of the page Bottom of the page
johnnyvision
Posted 2016-08-06 5:38 PM (#188025 - in reply to #188023)
Subject: Re: Anybody install their own Power Commander V?


Visionary

Posts: 4278
what did you ground it to. Go straight to frame.

do you have all wires pressed in tight

did you unhook 02's
Top of the page Bottom of the page
nailer
Posted 2016-08-06 6:11 PM (#188029 - in reply to #188025)
Subject: Re: Anybody install their own Power Commander V?


Tourer

Posts: 366
Albuquerque, NM		Grounded PCV to the bracket connected to the frame using a star washer. O2's are disconnected. Will recheck connecter seatings. There is about an inch and a half of clearance between the cylinder heads and the frame to disconnect the injector connectors. What a pain to get to!

Thnx JV.



(IMG_20160806_170256.jpg)



Attachments
----------------
Attachments IMG_20160806_170256.jpg (56KB - 0 downloads)
Top of the page Bottom of the page
nailer
Posted 2016-08-07 5:20 PM (#188037 - in reply to #188023)
Subject: RE: Anybody install their own Power Commander V?


Tourer

Posts: 366
Albuquerque, NM		Front cylinder injector connector wasn't fully seated. I also found the fuel tank vent "T" hose to the rear part of the throttle body was cracking in several places. Bike has much better throttle response in all gears. Had set my timing gear to -1 before the PCV due to pinging . Can probably move it in the plus direction with the new pcv map. $269 shipped w/6000 rpm rev limit from maniacmotorsports.com. Bike is ready for a trip to Iowa for cams from the Vic Shop.

Edited by nailer 2016-08-07 5:26 PM
Top of the page Bottom of the page
johnnyvision
Posted 2016-08-07 5:29 PM (#188038 - in reply to #188023)
Subject: Re: Anybody install their own Power Commander V?


Visionary

Posts: 4278
Rylan at the vic shop said for some reason vision run best a +3 I did +4 and on hot days above 95 degrees I would get pinging. +3 no problem
Happy for you
Top of the page Bottom of the page
johnnyvision
Posted 2016-08-07 5:30 PM (#188039 - in reply to #188023)
Subject: Re: Anybody install their own Power Commander V?


Visionary

Posts: 4278
PCV do not adjust the timing below 2500 just so you know
Top of the page Bottom of the page
johnnyvision
Posted 2016-08-07 6:00 PM (#188040 - in reply to #188023)
Subject: Re: Anybody install their own Power Commander V?


Visionary

Posts: 4278
nailer

please tell me more or photo of vent line T there should be no overflow going to throttle body. witch side of bike. I looked at mine and could not see one
Top of the page Bottom of the page
nailer
Posted 2016-08-07 8:05 PM (#188042 - in reply to #188040)
Subject: Re: Anybody install their own Power Commander V?


Tourer

Posts: 366
Albuquerque, NM		This is what I found on mine. It was above the intake boot pointing toward the rear cylinder. A vacuum line is what I mean.



(14706184416731998734742.jpg)



Attachments
----------------
Attachments 14706184416731998734742.jpg (35KB - 0 downloads)
Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [25 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread

Copyright © 2007-2024 Victory Riders Network™