|
|
Visionary
Posts: 1290
Ruskin, Fl | Anybody have their fuel door break? I opened it to get fuel and the plastic tab broke on one side. On the hinged side where the pin goes. It's never been stressed to my knowledge and I got the bike new. I have it removed now and plan on attempting JB Weld before I spend $140 bucks. I'll post some pics when I get done. I plan on grinding some of what little is left and embedding a metal washer in the epoxy for added strenth.
Edited by cw1115 2016-08-09 1:52 PM
|
|
| |
|
Visionary
Posts: 4278
| check the web there is some great plastic glues out there. I do think the plastic dry out is why they brake
http://www.ebay.com/itm/Victory-Vision-Motorcycle-Fuel-Door-Panel-w... |
|
| |
|
Visionary
Posts: 4278
| check the web there is some great plastic glues out there. I do think the plastic dry out is why they brake
http://www.ebay.com/itm/Victory-Vision-Motorcycle-Fuel-Door-Panel-w... |
|
| |
|
Visionary
Posts: 1290
Ruskin, Fl | Thanks Johnny. I have fixed the latch on the glovebox door on two different bikes with great success. I have an ingenious idea to reinforce the fuel door repair. I'll take pics. |
|
| |
|
Visionary
Posts: 1290
Ruskin, Fl | And I saw that. Only 30 bucks more for a new one without scratched. Of course I need Sunset Red, which it 10 dollars more. |
|
| |
|
Cruiser
Posts: 103
Davenport, IA | Well, mine broke as well last week on a long trip. Couldn't get the fuel door open. On the underside of the fairing, the tab broke, not allowing door to open when key is turned counterclockwise. Had to do some disassembling to fuel up, but got it opened. Duct tape was my best friend to secure it down after that. I have not taken it all apart yet, but will soon dive in to see if I can make the repair without buying the expensive piece. |
|
| |
|
Visionary
Posts: 1290
Ruskin, Fl | I had that happen on my 2008 kmt27. Same thing, pulled into a gas station on fumes and had to take bike apart. It is not the door itself. In my case and probably yours too the tank top has to be replaced. Here is how I fixed mine.
http://www.vision-riders.com/bb/forums/thread-view.asp?tid=12197&po...
Hope that helps. I don't know when it was redesigned, but it is new and improved on my 2013. |
|
| |
|
Cruiser
Posts: 103
Davenport, IA | Cw1115, thanks for your input. yes, I think mine is like your issue. Thanks for info on your repair. I will be doing some dissassembling soon to see what I need to do. |
|
| |
|
Tourer
Posts: 482
Beer Collins, Colorado (there is no fort) | My fuel door latch failed on tour and I was able to see the cable moving when the key was turned & managed to hook it through the edge of the fuel door with a piece of wire and get it opened up-I've since disabled the locking latch and mounted some very strong neodymium bar magnets that keep the hatch closed and and good push will flip it open. Maybe not as secure but very functional as long as the cover's still attached at the hinges. I looked at repairing the plastic tab that broke and it's a poor design that's gonna fail again. I believed they redesigned this on newer models (mine's an 09). |
|
| |
|
Visionary
Posts: 1290
Ruskin, Fl | Its redesigned for sure. But on my 2008 it was actually the tank top that broke, the tab that hold the cable sheath from moving. This time the tab on the door broke, where it pivots open. Almost done. Waiting on JB weld to set so I can grind it nice. Pics to follow. |
|
| |
|
Cruiser
Posts: 160
Lennox, SD | Mine broke 3 years ago after repeated complaints to Victory they replaced it. Originally they would not because it was "cosmetic" damage. Iargued with them because it was poor design on their part. It helps to trash them on social media. |
|
| |
|
Visionary
Posts: 1290
Ruskin, Fl | I posted some pics. Not pretty, but you can only see it while fueling, and it works perfectly.
http://www.vision-riders.com/bb/forums/thread-view.asp?tid=26016
Edited by cw1115 2016-08-14 8:25 PM
|
|
| |
|
Visionary
Posts: 1308
Sand Rock, AL United States | My latching mechanism is still working after 141,000 miles worth of gassing up, however , one of the hinges broke in 2012. The door has worked properly with one hinge ever since. i am careful when closing the door to hold the key to the left and press the door in place and return key to off position. I think that has been beneficial to the long life of my latch mechanism. I got that bit of information on this site years ago.  |
|
| |
|
Iron Butt
Posts: 804
Perry Hall, MD | Hey Michael, I love seeing examples of self engineering as impressive as what you demonstrated. Nice Job! |
|
| |
|
Cruiser
Posts: 222
Barefoot Bay, FL United States | you mean 'break', right?? |
|
| |
|
Visionary
Posts: 1290
Ruskin, Fl | However you say it, it is still in 2 pieces lol |
|
| |
Fuel door broke
