|
|
Tourer
Posts: 520
Simi Valley, CA | Thanks... too much |
|
| |
|
Cruiser
Posts: 134
, MO | Yea what I was thinking.. |
|
| |
|
Cruiser
Posts: 255
New Brunswick , Canada | Is the projection distorted by the vibration of the motor when idleling ? |
|
| |
|
Cruiser
Posts: 134
, MO | I haven't noticed any. I'll check if you want. |
|
| |
|
Cruiser
Posts: 134
, MO | No distortion while idling and can't see when riding. Here is a picture of the install from underneath the bike. Notice there is two holes. The empty hole was too far forward so I moved it closer to the tail light and now it can be seen with the right angle.
https://www.dropbox.com/s/t1v9nawc50e3vqh/Photo%20Jan%2015%2C%2010%2...
(Vicotry-projection-mount.png)
Attachments
----------------
 Vicotry-projection-mount.png (478KB - 17 downloads)
|
|
| |
|
Puddle Jumper
Posts: 12
| I've sent you an e-mail but my iphone is bugging out on sending them.
Did you get it from week before last.
I'd still like to get one from you and pay the price +4% for PP fees. |
|
| |
|
Cruiser
Posts: 134
, MO | No sir Dr, Never got it! ill pm you.. |
|
| |
|
Cruiser
Posts: 134
, MO | Got 2 left.. |
|
| |
|
Cruiser
Posts: 215
W'ford Tx | That is awfully neat-o. Price is right and would grab attention of everyone. Would you be able to make a template as far as where to drill the hole. I have a chrome rear and would only want to put the one needed hole in it. |
|
| |
|
Fountain Inn, SC United States | Nice job Bill! Have you had to clean the lens from road dirt/grime? Am I right to think that the higher it's mounted, the larger the image? Is it optimized for a particular height to be in focus? |
|
| |
|
Cruiser
Posts: 134
, MO | Yes sir Jeff you are correct! I didn't check for optimize just set it for what size I preferred. It was still In focus from bottom of trunk area. I wiped it off once from road grime, I'm gonna mount a little visor in front of it to see if that helps a little but it's not too bad so far! |
|
| |
|
Cruiser
Posts: 134
, MO | Goat I could give you measurements of mine! |
|
| |
|
Puddle Jumper
Posts: 12
| I've been unable to get back here. The forum wouldn't let me on.
I tried sending PP but it kept getting kicked back.
I sent you a PM.
Is this a sign? Am I jinxed with this Vision?
I waited over 2 months for a custom EXPENSIVE part from a vendor. He posted photos of these things that others was getting but I wasn't getting mine.
Finally he refunded my money without me asking for it back. (I wanted the part more!)
I think he just got tired of me asking when I would get it. He promised it back in Dec.
I only asked every other week in an e-mail or PM and I asked nicely.
Now this fiasco on the other thing I wanted for the bike.
I'm beginning to think my Vision doesn't want new things added. It's jinxed. |
|
| |
|
Cruiser
Posts: 215
Boydsville, AR United States | Could someone get me a measurement from the center of the hole to the edge of the red plastic on the tailight? I have one, and would like to get it right the first time.
Thanks, |
|
| |
|
Cruiser
Posts: 215
Boydsville, AR United States | Could someone get me a measurement from the center of the hole to the edge of the red plastic on the tailight? I have one, and would like to get it right the first time.
Thanks, |
|
| |
|
Cruiser
Posts: 134
, MO | I'll measure today for you... |
|
| |
|
Cruiser
Posts: 134
, MO | Dr what are you talking about? If your talking about messaging me you are incorrect. |
|
| |
|
Cruiser
Posts: 134
, MO | Dr I responded to you on several occasions with the right payola address. It's not my fault if you are having forum problems, I have sent to everyone that has purchased without hesitation and if you think they are too expensive than don't order, go get one made for yourself and see what it costs. |
|
| |
|
Cruiser
Posts: 134
, MO | Wseeman it's 1.5 inches to center on mine |
|
| |
|
Cruiser
Posts: 134
, MO | Ok, i have to put a hold on orders. I can't get my supplier in California to return emails or calls. I have $800 worth of orders with him on these and other stuff and feel like im getting the run around. I will be returning monies until the order comes in, it's been a month and too long for my liking. I will let you know when i hear something asap.
Thanks |
|
| |
|
New user
Posts: 3
| Just came acros your post and I think this is an awesome idea. Will you be able to ship one to Sydney Australia at all? Let me know the cost and payment options if that is the case.
Edited by janobar 2013-05-27 8:38 PM
|
|
| |
|
Puddle Jumper
Posts: 16
| Hope you get the orders straightened out. This is entirely too cool.  |
|
| |
|
New user
Posts: 3
| Managed to install the projection logo link below. Let me know if you are interested in getting one. Just realised I should twist the projection 180 degrees.
http://youtu.be/HnYjagtakqU
|
|
| |
|
Puddle Jumper
Posts: 25
SE Wisconsin | I posted pic's on my ( victoryhour ) gallery of the Victory LED logo. I put it on the right side of the bike so when it's parked it can be seen. Hooked it up to a toggle switch in the left tank box. I can use it with or without the blue LED's on. I might need to adjust it some. |
|
| |
|
New user
Posts: 3
| Here are pictures also the design is slightly different it has a circle around it and some more detalis.
Edited by janobar 2013-06-07 6:04 AM
(led-logo1.jpg)
(led-logo2.jpg)
Attachments
----------------
led-logo1.jpg (190KB - 2 downloads)
led-logo2.jpg (179KB - 1 downloads)
|
|
| |
Victory logo led
