You are currently not logged in.  Logon or register to access more features. Vision-Riders.com is a FREE service provided by Victory Riders Network.

Search:




mounting/dismounting
Jump to page : 1 2
Now viewing page 2 [25 messages per page]
View previous thread :: View next thread
   Discussion -> Vision DiscussionMessage format
 
varyder
Posted 2013-06-07 5:06 PM (#140096 - in reply to #139769)
Subject: Re: mounting/dismounting


Visionary

Posts: 8144
New Bohemia, VA
this thread makes me wonder if some should even be near a motorcycle, much less a 4 wheel or above vehicle.
Top of the page Bottom of the page
wdwurker
Posted 2013-06-07 8:42 PM (#140099 - in reply to #140036)
Subject: Re: mounting/dismounting


Cruiser

Posts: 92
amessen - 2013-06-06 10:15 AM

Well I am 6' 10" and 32 inch inseam but with almost 62 years under my belt and all the agility of a bump on a log I found out that putting a Corbin with Drivers backrest I had to do a lot of adjustments to getting on and off. I stand beside the bike and grab my boot or pant leg and go straight over the saddle then sit down. Off is just the reverse standup lift right leg grab pant leg or boot and pull it over it may not be a graceful as some but it hurts less and with my back and legs I just want on so I can ride. Archie


That's me too but since I put the drivers backrest on, it's a careful trip over the tank/dash with a good grip on my pant leg. Getting off the bike is not as easy for me though. With two bad knees, it's more of a hop...hop...drag as I drag my right boot across the top of the saddle (usually pulling my gel pad from its assigned position). Not at all graceful but like someone else said... I bought it to ride, not compete in a beauty contest.

Edited by wdwurker 2013-06-07 8:44 PM
Top of the page Bottom of the page
Monkeyman
Posted 2013-06-07 8:57 PM (#140100 - in reply to #139769)
Subject: Re: mounting/dismounting


Iron Butt

Posts: 1066
Peru, IN
My Utopia backrest sort of folds down some (each of 2 hinges moves opposite each other...kinda forms a Z). That gets it out of the way enough for my fat legs to clear it (more or less). It doesn't get out of the way as much as some I've seen on GWs, but I'd never get on the bike if it didn't pivot. I'm guessing the Vic backrest doesn't pivot?
Top of the page Bottom of the page
victoryvisiontour
Posted 2013-06-08 8:53 AM (#140107 - in reply to #139769)
Subject: Re: mounting/dismounting


Iron Butt

Posts: 763
Anderson, IN (48mi NE of downtown Indianapolis)
Is this thread serious?
Top of the page Bottom of the page
varyder
Posted 2013-06-08 9:04 AM (#140109 - in reply to #140107)
Subject: Re: mounting/dismounting


Visionary

Posts: 8144
New Bohemia, VA

victoryvisiontour - 2013-06-08 9:53 AM Is this thread serious?

Sadly, yes.

Top of the page Bottom of the page
jimtom
Posted 2013-06-08 9:04 AM (#140110 - in reply to #140109)
Subject: Re: mounting/dismounting


Visionary

Posts: 1308
Sand Rock, AL United States
hahahahaha!!!
Top of the page Bottom of the page
Allen_B
Posted 2013-06-08 10:34 AM (#140111 - in reply to #139769)
Subject: Re: mounting/dismounting


Cruiser

Posts: 106
Clinton, CT
I guess it is better than another oil or darkside thread.

Nevermind....

Allen
Top of the page Bottom of the page
Monkeyman
Posted 2013-06-08 12:02 PM (#140112 - in reply to #139769)
Subject: Re: mounting/dismounting


Iron Butt

Posts: 1066
Peru, IN
I use full synthetic Rotella AMSOIL oil (20w40) in my car tire on the front of my bike.
Top of the page Bottom of the page
Jump to page : 1 2
Now viewing page 2 [25 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread

Copyright © 2007-2025 Victory Riders Network™