|
|
Puddle Jumper
Posts: 32 shelbyville tennessee | I can,t find the factory bottom wind defectors on any of the victory sites, i want to order them.
Any one have a link ? |
|
|
|
Tourer
Posts: 550 Tacoma, WA | Nope. I was told they were an experiment when I did the Victory test ride tour. ---Metalguy |
|
|
|
Puddle Jumper
Posts: 32 shelbyville tennessee | Ok thanks metal. |
|
|
|
Tourer
Posts: 495 Carrollton, TX | These lower wind deflectors should be available any day now. The part number for them is 2876259 and they are priced at $229.99. They were to be available on 4-1-08. I have a set on order but they have not come in yet. |
|
|
|
Tourer
Posts: 550 Tacoma, WA | Geez! they sure are proudof the plasic, huh? ----Metalguy |
|
|
|
Cruiser
Posts: 109
| i am glad we have determined young soldiers as you metal guy
thanks for the service |
|
|
|
Tourer
Posts: 550 Tacoma, WA | Young? Thanks!!! Just doing my job. -----Metalguy |
|
|
|
Visionary
Posts: 2026 Brighton, TN | I have been tossing the idea around that the mounts can't be that hard to fabricate. Two mounting locations onto a piece of plexiglas and wala. I have looked in the hardware store for a hinge that I could use, flat on one side, to put double sided tape to it for mounting. Then any kind of other end to attach to the plexi. Was looking for it to have multiple stops or even wing nuts to be able to tighten at this point to give the ability to position them in or out or midway.
I am still in the throws of patch that is kicking my butt. Don't know If I want to tackle metal yet. Maybe when I'm done with the patch then I move on to metal fabrication. |
|
|
|
Puddle Jumper
Posts: 17 MN | I've been thinking of adding a AC bezel through the inner fairing. Has anyone tried that yet? Here is the web page for a potential supplier.
http://www.rbsauto.com/product.asp?Product_Id=171040&d_Id=17183&l1=... |
|
|
|
Visionary
Posts: 1484 LaPorte,Tx. | If I do anything that is what I will probably do. I have been looking at the Goldwing vents and how to fit to the faring, shouldn't be too hard to accomplish. But, so far the temp has not been that bad, so we will see. |
|
|
|
Iron Butt
Posts: 721
| Actually I was thinking of contacting Baker Products, the maker of Baker Air Wings for many different bikes. They have many different kits and I was thinking that something that they currently make should work for the Vision, plus they come in different colors such as clear, light smoke, smoke, red, yellow, blue, and I think orange, basically their colors are meant to compliment the Honda Goldwing colors. Here is their link:
http://www.bakerbuilt.com/
Edited by Travelin' Man 2008-04-14 9:16 PM
|
|
|
|
Tourer
Posts: 353
| VisionTex - 2008-04-14 10:46 AM
If I do anything that is what I will probably do. I have been looking at the Goldwing vents and how to fit to the faring, shouldn't be too hard to accomplish. But, so far the temp has not been that bad, so we will see.
Finally had a 95 degree day here in central Cal, the Vision didn't feel any more uncomfortable in that temp than my 8-Ball does and I did have the opportunity to ride it in stop and go traffic, I personally didn't like the look of the deflectors and am glad I won't need them. |
|
|
|
Cruiser
Posts: 196
| My dealer got with the DM and said these would be available around April 1st.
When I got them to check again on Tuesday 4/15, they were told maybe mid May now....
Seems like when I was waiting for my ride, Sept.... Oct.... arrived in Nov.
Dejavue...all over again! |
|
|